CONGRATULATIONS on your new Jungle Jumparoo! We are so excited that you are now a part of the Jungle Jumparoo family! We hope you have years of fun ahead with your new Jungle Jumparoo! Below you will find assembly instructions and tips on care for your Jungle Jumparoo and Accessories!

  • Before you begin to assemble your Jungle Jumparoo, please note the following: Do not over tighten the bolts, this can damage the treads making it impossible to take your Jungle Jumparoo apart and reassembling at another time. 


  • To move your Jungle Jumparoo through a doorway simply remove the tube from the cage, remove the set screw in the base and remove the 2 base connectors. When walking through the doorway simply pinch the 2 sections together.

  • Once your Jungle Jumparoo is completely assembled, adjust the metal slide on the swing to create a loop in the rope

  • Take the loop created in the rope and the blue hang bar and place over the swing bar or the side of the octagon passing the blue hang bar through the loop

  • You can then adjust the rope handle height as desired with the metal slider or by winding and looping the rope around the octagon or bar.

  • Make sure there is no open loop in the rope

    • Remove tube from the Jungle Jumparoo frame.

    • Inflate or deflate the tube partially, so it holds the form but the cover is not stretched while installing, not doing so will result in over stretching the seams of the cover, runs in the fabric and premature ripping of the seams.

    •  With the tube standing vertical in front of you place the cover over the top of the tube with the logo facing outward.

    • Then take the velcro strap on that color block matching with the loop on the same color block, work your way around the tube adhering the cover straps around the tube as you go.

    • Begin to add air to the tube a little at a time, adjusting the tube in the cover as needed. Do not over-­inflate the tube, fill until the tube fits comfortably within the cover. The tube cover will fit snug, but not tight on the tube, there will be no pulling on the seams of the cover. There will be a 2 inch gap of black tube showing on the underside when properly inflated and the straps should not be pulled too tight.

    • Place the covered tube over the frame of your Jungle Jumparoo and ENJOY!

      • Place Sprinkler on top of Jungle Jumparoo octagon, can can attach the sprinkler facing upward or downward.

      • Attach 2 provided straps around each side of sprinkler to the sides of the octagon

      •  Slide the hose under the inner tube, or drape over the inner tube based on your preference and attach the hose to the Turret Sprinkler

      • Secure the sprinkler to one of the poles with the final strap

      • Turn dial on sprinkler to try out the different water stream patterns

      • Have a BLAST!!!

      • To inflate your Inner Tube, you will need a standard air compressor with an attachment like that use for car tires, to ensure proper inflation we recommend using the start\stop method; small burst of air then stop, continue until full. This keeps the tube round and helps the air disperse within the tube evenly.

      • There is no PSI reading on the tube due to the lack of an outer tire

      • The Large Inner tube will stand about 16 inches high and the Mini tube about 12 inches high when properly inflated

      • During inflation If you notice any asymmetry in your tube remove any air in the tube and re-inflate slowly using the stop and start air flow method to prevent bulging.

      • Due to the heavy rubber compound it can take a few weeks for your tube to break-in and may require more air, we recommend filling the tube slowly and adding more as needed. Inflating the tube too quickly or over inflation of the tube will decrease the lifespan and can also cause bulging.

      • If you encounter a slow leak in your new inner tube it is likely due to a loose inner valve stem core. If this part is not tightened all the way it will allow air to slowly leak over time. Use a small pair of tweezers or the valve tool that came with your Jungle Jumparoo to tighten this part by turning the inner pin in the valve stem clockwise (to the right) until it stops. You can also remove this part to deflate the inner tube quickly by unscrewing this part counterclockwise (to the left). 

        The Jungle Jumparoo Tube has been specifically tested to withstand the impact of jumping and is made from the heaviest premium rubber compound on the market and there are a few key steps you can take to ensure the longevity of your Inner Tube:
        • Avoid abrasive or corrosive chemicals, such as pool treatment chemicals, motor oil, industrial cleaning solutions, sharp objects, high heels, sports cleats, weed whackers lawn mowers etc.

        • Avoid Sunlight/UV exposure, we suggest using the Tube Cover and the All-Weather Cover to protect the Inner Tube when enjoying the Jungle Jumparoo outdoors. The Jungle Jumparoo Tube Cover is not UV resistant and will fade when used outdoors, but adds an extra layer of protection, helps prevent tube splits, bulging, adds traction when using the Turret Sprinkler and protect little feet from a hot tube. 

        • Avoid extreme temperatures hot and cold, remove air for the hotter summer months

        • Under inflation or Over inflation, long periods of disuse (such as seasonal storage)

          • Inner tubes that are used often will last longer as this maintains the elasticity and flexibly of the rubber. During the manufacturing process, the tube manufacturer adds a protective compound to the rubber formula. Regular use causes the inner tube to flex and compress, pushing this protective substance to the surface. This doesn’t happen in an unused inner tube, so the rubber is more vulnerable to damage from ozone and oxidation.Tubes that are stored over the winter are more likely to have rubber rot and develop holes when inflated in the spring. If you must store the tube deflate, store in a plastic bag in a cool dark location. However, this does not guarantee that there will be no rubber rot.
        Over or improper inflation, bulging, outdoor use and storage without proper protection, seasonal storage and contact with sharp objects are not covered by warranty.